Статьи журнала - НБИ технологии

Все статьи: 502

The investigation of thermal power characteristics of wood pulp

The investigation of thermal power characteristics of wood pulp

Yalechko Vladimir Ivanovich, Kochubey Viktoriya Vitalyevna, Gnatishin Yaroslav Mikhaylovich, Dzyadevich Boris Nikolaevich, Zaikov Gennadiy Efremovich

Статья научная

To study the heating value of wood we used integrated thermal analysis. We have studied the aspen wood aged 10 years. For sample 3 (bark), which is characterized by the largest coke residue, the heterogeneous oxidation process occurs most rapidly. The thermal analysis shows that the pattern of the cortex has the highest heating value.

Бесплатно

The method for lifetime estimation through the mechanical properties in tension

The method for lifetime estimation through the mechanical properties in tension

Bakhracheva Yuliya Sagidullovna

Статья научная

The method for prediction of Paris' curve shape through the results of tensile test is suggested. For this purpose the author developed non-direct method for determination of Kth and Kfc and corresponding to them da/dN values. The relationship between Kth and b/y ratio was found. The correlation Kfc(KIc) was also shown. It makes possible to estimate lifetime of different structures with cracks under cyclic loading.

Бесплатно

The method of increasing the thermostability of filled polymers

The method of increasing the thermostability of filled polymers

Prokopchuk Nikolay Romanovich, Lenartovich Liliya Alekseevna

Статья научная

The individual contribution of stabilizers and fillers into the increase of thermal stability of a polymer-matrix of composite materials at their joint presence in the composite is estimated in this paper. The increase of thermal stability of polypropylene composites in the process of pre-saturation of the surface of fillers by thermal stabilizers compared to their individual introduction into the polymer is determined. A method of saturation of the surface of fillers by stabilizers is proposed. The mechanism of a prolonged and direct action of stabilizers desorbing from the surface of the filler is explained. It leads to the increase of the thermal stability of stabilized filled polypropylene compositions obtained by the proposed method by 10-40 % in comparison with the traditional one. It simultaneously reduces the amount of used stabilizers in 1.25 times.

Бесплатно

The reinforcement of particulate-filled polymer nanocomposites by nanoparticles aggregates

The reinforcement of particulate-filled polymer nanocomposites by nanoparticles aggregates

Kozlov Georgiy Vladimirovich, Mikitaev Abdullah Kasbulatovich

Статья научная

The applicability of irreversible aggregation model for theoretical description of nanofiller particles aggregation process in polymer nanocomposites has been shown. The main factors, influencing nanoparticles aggregation process, were revealed. It has been shown that strongly expressed particulate nanofiller particles aggregation results in sharp (in about 4 times) formed fractal aggregates real elasticity modulus reduction. Nanofiller particles aggregation is realized by cluster-cluster mechanism and results in the formed fractal aggregates density essential reduction, that is the cause of their elasticity modulus decrease. As distinct from microcomposites, nanocomposites require consideration of interfacial effects for elasticity modulus correct description in virtue of a well-known large fraction of phases division surfaces for them.

Бесплатно

Ultrathin poly (3-hydroxybutyrate) fibers: structure and dynamic characteristics

Ultrathin poly (3-hydroxybutyrate) fibers: structure and dynamic characteristics

Karpova Svetlana Gennadyevna, Iordanskiy Aleksey Leonidovich, Motyakin Mikhail Viktorovich, Olkhov Anatoliy Aleksandrovich, Lomakin Sergey Modestovich, Berlin Aleksandr Aleksandrovich

Статья научная

Structural and dynamic analysis based on combined thermophysical and molecular-mobility measurements via spin-probe ESR spectroscopy has been applied to films and fibrous matrixes based on poly(3-hydroxybutyrate). The dynamic behaviors of partially crystalline samples during deformation under conditions of electrospinning and cold rolling have been compared. The comparative results of the complex investigation of films and ultrathin fibers in the poly(3-hydro-xybutyrate) matrix have shown that the electromechanical action leads to additional crystallization of the crystalline regions, spherulites, and lamellas in the polymer. The changes in the crystalline phase of the polymer are accompanied by an increase in the packing density of macromolecules in the intercrystalline space. With the use of the spin-probe ESR method, the effect of water and the oxidant ozone on the morphology of the amorphous phase of poly(3-hydroxybutyrate) ultrathin fibers has been determined. The measurements of the dynamics of spin-probe rotation in samples before and after cold rolling have shown that the additional orientation of poly(3-hydroxybutyrate) spherulites in a mechanical field results in stabilization of amorphous regions more resistant to the aggressive effects of ozone.

Бесплатно

Vacancy transport properties in boron-carbon bc3 nanotubes

Vacancy transport properties in boron-carbon bc3 nanotubes

Boroznin Sergey V., Zaporotskova Irina V., Boroznina Natalya P., Zaporotskov Pavel A., Kislova Tatyana V., Akatiev Vladimir V., Yarmak Vladimir A.

Статья научная

The paper presents results of theoretical research into vacancy formation in B type of boron-carbon nanotubes ВС n, where n = 3. The research was performed using the MNDO method within the framework of an ionic-embedded covalent-cyclic cluster model, molecular cluster model and DFT method. We found that when a V -defect (vacancy) is introduced in a boron-carbon nanotube, the band gap of the defective tubules increases. It means that physical properties of materials can be purposefully changed by introducing defects. Vacancy migration along the atomic bonds in the tubule was simulated and vacancy transport properties were studied. It was found that the defect migration along different bonds actually represents the process of carbon or boron ions hopping between their stable states on the nanotube surface. The calculated activation energy values revealed dependence of ionic conductivity in boron-carbon tubules on temperature.

Бесплатно

Valve cam design using numerical step-by-step method

Valve cam design using numerical step-by-step method

Vasilyev Aleksandr Viktorovich, Bakhracheva Yuliya Sagidullovna, Kabore Ousman, Zelenskiy Yuriy Olegovich

Статья научная

This article studies the numerical step-by-step method of cam profile design. The results of the study are used for designing the internal combustion engine valve gear. This method allows to profile the peak efficiency of cams in view of many restrictions, connected with valve gear serviceability and reliability.

Бесплатно

Ways of regulation of release of medicinal substances from the chitosan films

Ways of regulation of release of medicinal substances from the chitosan films

Kulish Elena Ivanovna, Shurshina Anzhela Samatovna, Pearce Eli M.

Статья научная

The article studies the chitosan films obtained by applying acetic acid and two antibiotics of cephalosporin and aminoglycoside type. It investigates the possibility of their transport properties regulation in the sphere of medicines manufacture. This regulation can be carried out by films with thermal modification implying the heating of formed films at the temperature of about 120 °C and reaction with sodium dodecyl sulphate. The article shows that the antibiotics release from films will be determined by the amount of antibiotics connected with chitosan by hydrogen bonds, on the one hand, and by the state of the polymer matrix, on the other hand.

Бесплатно

Wide-pore cryogels prepared using the combination of liquid-liquid phase separation and cryotropic gel-formation processes

Wide-pore cryogels prepared using the combination of liquid-liquid phase separation and cryotropic gel-formation processes

Lozinskiy Vladimir Iosifovich, Antonov Yuriy Alekseevich, Damshkaln Liliya Grigoryevna, Ezernitskaya Mariam Grigoryevna, Glotova Yuliya Konstantinovna

Статья научная

Novel, previously unknown, wide pore poly(vinyl alcohol) cryogels (PVACGs) have been prepared through the cryotropic gelation approach, when water-PVA-gum Arabic (GuAr) ternary liquid systems were used as feeds. The following set of conditions necessary for obtaining wide-porous, permeable for a water flow, and, simultaneously, mechanically strong enough PVACGs was established: the total concentration of gelling component - PVA (MW of 86 kDa) and non-gelling polymer - GuAr (MW of ~650 kDa) should exceed ~14 wt. %, GuAr/PVA ratio should be near 1 : 1 (w/w), and the feed’s pH should be within the range of ~5-11. The phase diagrams for the water-PVA-GuAr ternary liquid systems at pH 5.3 and 10.0 have demonstrated that such “optimum” compositions are in the vicinity of the rectilinear diameters of the respective diagrams, and that the limit of GuAr solubility in the PVA-rich phase is small. In such cases this GuAr fraction strongly binds with PVA, especially under alkaline conditions, within the forming gel phase of heterophase PVACG. The light microscopy studies revealed the presence of at least three distinct kinds of pores in these cryogels. Firstly, there are interconnected channel-like gross pores with cross-section of 100-200 µm which are the replicas of continuous GuAr-rich phase in the two-phase polymeric systems appearing due to the liquid-liquid phase separation in the ternary water-PVA-GuAr system. The second type is represented by isolated roundish large pores ca. 10-70 µm in diameter being the replicas of GuAr-rich phase dispersed as liquid droplets in the PVA-rich phase. And the third type is represented by the smaller rounded pores ~1-5 µm in diameter being the replicas of ice polycrystals. Such sophisticated “poly-porous” morphology of the studied PVA cryogels is their unique feature distinguishing them from other known PVA cryogels.

Бесплатно

Автоматизированные системы управления рисками

Автоматизированные системы управления рисками

Кадыров Аманулла Азизович, Кадырова Азиза Амануллаевна

Статья научная

В работе проводится анализ структурно-логической схемы управления рисками. Показано, что одним из наиболее «риск-несущих» составляющих опасных производственных объектов являются технические устройства. Одновременно максимальный уровень автоматизации возможен для технических устройств применительно к задачам их технического обслуживания, ремонта и управления рисками.

Бесплатно

Активизация инновационной деятельности малых производственных предприятий в реализации промышленной политики региона

Активизация инновационной деятельности малых производственных предприятий в реализации промышленной политики региона

Гришин Игорь Александрович

Статья научная

В статье рассмотрены основные подходы, формы и методы активизации инновационной деятельности малых производственных предприятий в процессе реализации региональной промышленной политики. На базе авторской классификации инноваций в сфере деятельности малых производственных предприятий разработана модель построения регионального кластера на основе стимулирования кооперационных и интеграционных связей промышленных предприятий. В формате предложенной кластерной модели спрогнозированы возможные сценарии инновационной модернизации регионального производственного комплекса и даны рекомендации по реализации их стратегии развития.

Бесплатно

Актуальные вопросы формирования и управления инфраструктурным потенциалом регионального продовольственного комплекса

Актуальные вопросы формирования и управления инфраструктурным потенциалом регионального продовольственного комплекса

Небогатикова Наталья Геннадьевна, Гапоненко Юлия Владимировна

Статья научная

В статье раскрывается определенная неравномерность и разновременность становления основных институтов рыночной системы. Среди подобных институтов важное место занимает продовольственный комплекс. Как показала практика, реализация инфраструктурного потенциала продовольственного комплекса превратилась в реальный фактор ускоренного становления рыночных форм хозяйствования.

Бесплатно

Актуальные проблемы моделирования социальных систем в условиях цифровой экономики

Актуальные проблемы моделирования социальных систем в условиях цифровой экономики

Кузнецова Майя Анатольевна

Статья научная

В статье анализируются факторы, влияющие на функционирование социальных систем, особенности и перспективы их развития в условиях становления цифровой экономики. Рассмотрены некоторые параметры, характеризующие общество как социальную систему.

Бесплатно

Алгебраические условия разрешимости проблемы устойчивости в задачах синтеза систем аварийной стабилизации

Алгебраические условия разрешимости проблемы устойчивости в задачах синтеза систем аварийной стабилизации

Рыжов Евгений Николаевич, Григорьева Ольга Евгеньевна

Статья научная

В статье в свете теории групп Ли предложены критерии разрешимости задач синтеза аварийной стабилизации. Данные критерии позволяют строить алгебры Ли для подобного класса задач.

Бесплатно

Алгоритм оптимального выбора архитектуры комплексной системы защиты информации с учетом специфики объекта и взаимодействия модулей защиты

Алгоритм оптимального выбора архитектуры комплексной системы защиты информации с учетом специфики объекта и взаимодействия модулей защиты

Зангиев Таймураз Таймуразович, Тарасов Елизар Саввич, Сотников Владимир Владимирович, Тугушева Залина Якубовна, Гунай Фатима Рашидовна

Статья научная

В статье приведены актуальные проблемы, связанные с учетом противоречивых требований при проектировании комплексных систем защиты информации (КСЗИ). Предложен подход к выбору и конфигурации средств КСЗИ, основанный на ролевой модели М. Белбина в интерпретации КСЗИ как команды, которая позволит выстроить целостный контур защиты информации. Продемонстрированы случаи проявления синергизма и эмерджентности, обеспечивающие эффективное функционирование системы.

Бесплатно

Анализ видеокодека VP9, применяемого в мультипротокольной платформе JITSI

Анализ видеокодека VP9, применяемого в мультипротокольной платформе JITSI

Керенцева Нина Дмитриевна, Трофимов Александр Игоревич, Галич Сергей Владимирович

Статья научная

В статье проведен сравнительный анализ различных видеокодеков, которые используются в мультипротокольной платформе Jitsi Meet основанной на технологии WebRTC. Также рассмотрены плюсы и минусы каждого видеокодека в отдельности. Приведены результаты нагрузочного тестирования данной платформы.

Бесплатно

Анализ влияния аутсорсинга на инновационное развитие предприятий

Анализ влияния аутсорсинга на инновационное развитие предприятий

Ляшенко Александр Викторович

Статья

Бесплатно

Анализ влияния микроволнового излучения сотовой связи на человека

Анализ влияния микроволнового излучения сотовой связи на человека

Черных Сергей Викторович

Статья научная

Проведен анализ многочисленных точек зрения на проблему влияния микроволнового излучения сотовой связи на человека, получены оценки интенсивности электромагнитного поля сотовой связи для различных ситуаций, наиболее часто встречающихся в повседневной жизни. На основе проведенного анализа и полученных оценок сделана попытка прогноза дальнейшего развития сотовой связи.

Бесплатно

Анализ закономерностей последовательного развития явлений самоорганизации на предприятиях

Анализ закономерностей последовательного развития явлений самоорганизации на предприятиях

Семенова Лидия Михайловна, Хлебников Владимир Борисович, Бахрачева Юлия Сагидулловна

Статья научная

В статье рассмотрена возможность повышения качества управления предприятием с позиций синергетики. Анализируются основные закономерности эволюции явлений сомоорганизации и предпосылки перехода предприятия на новый режим функционирования.

Бесплатно

Журнал