Machinability of stainless tool steel using nitrogen oil-mist coalant
Автор: Elshwain Amad E., Elmunafi Mohamed H., Yusof Noordin M., Redzuan Norizah, Kurniawan Denni, Wahab Hassan A., Mohamed Yasir A.
Рубрика: Химическая технология
Статья в выпуске: 3 (73), 2017 года.
For all dry machining process, temperature generated in the cutting zone is the major challenge. It causes tool failure and results in unsatisfactory surface finish. Application of flood coolant method during machining processes can significantly reduce the temperature and consequently extend the cutting tool life. However, it has serious concerns regarding environmental pollution, operator health and manufacturing cost. These issues are usually attempts to be overcame by using minimum quantity lubrication (MQL) technique. This method merges the advantages of both dry cutting and flood cooling by spraying a small amount of lubricant to the cutting zone using vegetable oil. In this paper, another technique is proposed in order to further enhance the machineability of the stainless tool steel (STAVAX ESR 48 HRC). This involves using of nitrogen gas (N2) and air as cooling medium in combination with oil mist lubricant (MQL). The results show that the combination between nitrogen and oil-mist lubricant much more prolonged the tool life and improved the surface finish than the air-oil mist lubricant medium.
Mql, cutting fluid, tool wear, cutting forces, surface roughness, tool life, nitrogen
Короткий адрес: https://readera.org/140229414
IDR: 140229414 | DOI: 10.20914/2310-1202-2017-3-143-147
Список литературы Machinability of stainless tool steel using nitrogen oil-mist coalant
- Elmunafi M. H., Kurniawan D., Noordin M. Y. Use of castor oil as cutting fluid in machining of hardened stainless steel with minimum quantity of lubricant. Procedia CIRP. 2015. vol. 26. pp. 408-411.
- Rahim E. A. Ibrahim M. R., Rahim A. A., Aziz S. et al. Experimental investigation of minimum quantity lubrication (MQL) as a sustainable cooling technique. Procedia CIRP. 2015. vol. 26. pp. 351-354.
- Sreejith P. Machining of 6061 aluminum alloy with MQL, dry and flooded lubricant conditions. Materials letters. 2008. vol. 62. pp. 276-278
- Zhang S., Li J.F., Wang Y.W. Tool life and cutting forces in end milling Inconel 718 under dry and minimum quantity cooling lubrication cutting conditions. Journal of Cleaner Production. 2012. vol. 32. pp. 81-87.
- Sharma J., Balwinder S. S. Investigation of effects of dry and near dry machining on AISI D2 steel using vegetable oil. Journal of Cleaner Production. 2014. vol. 66. pp. 619-623.
- Handawi M., Elshwain A.E., Noordin M. Y., Redzuan N. et al. Comparison between Nitrogen-Oil-Mist and Air-Oil-Mist Condition when Turning of Hardened Tool Stainless Steel. Applied Mechanics and Materials. 2014. vol. 660. pp. 18-22.
- Shizuka H., Sakai K., Suzuki Y. The Assist Effect of Nitrogen Atmosphere on MQL Cutting Performance. Key Engineering Materials. 2009. vol. 407. pp. 321-324
- Shaw M. C. Metal cutting principles. Clarendon press Oxford. 2005. pp. 30-90
- Gillibrand D., Sarwar M., Pierce C. The economic benefit of finish turning with coated carbide. Surface and Coatings Technology. 1996. vol. 86. pp. 809-813
- Noordin M. Y., Kurniawan D., Sharif S. Hard turning of stainless steel using wiper coated carbide tool. In-ternational Journal of Precision Technology. 2007. vol. 2007. pp. 75-84
- Çakır O., Kıyak M., Altan E. Comparison of gases applications to wet and dry cuttings in turning. Journal of Materials Processing Technology. 2004. vol. 153. pp. 35-41
- Zhao W., He N., Li L. Effect Mechanism of Nitrogen Gas on Chip Formation in High Speed Cutting of Ti6Al4V Alloy Based on FEM Simulation. Materials Science Forum. 2009. pp. 177-182
- Chandrasekaran V. V., Payton L. N., Hunko W. S. Performance of Nitrogen and Liquid Nitrogen as Cool-ants in Orthogonal Machining of AISI 1020 Steel Alloy With Uncoated Carbide Tools. In ASME International Me-chanical Engineering Congress and Exposition, American Society of Mechanical Engineers. 2014. pp. V02BT02A036-V02BT02A036.
- Diniz A.E., Machado Á. R., Corrêa J. G. Tool wear mechanisms in the machining of steels and stainless steels. The International Journal of Advanced Manufacturing Technology. 2016. vol. 87. pp. 3157-3168..